Ombre Stuffed Amigurumi Pumpkin Crochet Pattern

Abdessamad avatar
Ombre Stuffed Amigurumi Pumpkin Crochet Pattern

The Ombre Stuffed Amigurumi Pumpkin is a plush pumpkin made in gradient yarn, worked entirely in the round in a continuous spiral of tight single crochet and finished with a ribbon stem. It is an easy to advanced beginner pattern. The finished pumpkin is about 4 inches in diameter and 3 inches tall, depending on how tightly you cinch it, and it suits a Thanksgiving table, a mantel or a host gift.

Stitch abbreviations

sc = single crochet, inc = increase (2 sc in one stitch), dec = invisible decrease, rnd = round, st(s) = stitch(es).

Skill, size and gauge

Skill Level: Easy / Advanced Beginner. You will need to know how to work in a continuous spiral, increase, and decrease. The sculpting technique is straightforward and perfect for beginners looking to learn soft-shaping. Finished Size: Approximately 4 inches in diameter and 3 inches tall, depending on how tightly you cinch the segments. Gauge: 5 sts and 5 rnds = 1 inch in single crochet. Exact gauge is not critical, but ensure your stitches are tight enough that stuffing does not show through.

Method at a glance

This Ombre Stuffed Amigurumi Pumpkin is constructed in three main phases, making it an incredibly satisfying and logical project to follow. First, you will crochet the main body of the pumpkin from the top down. Starting with a magic ring using the brightest orange section of your gradient yarn, you will work a series of increase rounds to establish the width, followed by several even rounds where the magic of the color-shifting yarn will naturally transition into a deeper reddish-orange. Next, you will work the decrease rounds to close the sphere, pausing to stuff the pumpkin very firmly before fastening off and leaving a uniquely long yarn tail. Finally, that long tail is used for the sculpting phase. By threading the yarn through the center of the pumpkin and pulling tightly over the outside edges, you will compress the stuffing to form 6 to 8 deep, characteristic pumpkin lobes. Once the body is shaped, a simple folded loop of ribbon is glued into the top indentation to act as a sweet, rustic stem.

Materials and tools

  • Yarn: Worsted weight (Category 4) acrylic or cotton amigurumi yarn in an orange-to-red ombre/gradient colorway. You will need approximately 50-60 yards per pumpkin.
  • Hook: 4.0mm (Size G) crochet hook (or size needed to obtain a tight, dense fabric).
  • Stuffing: High-quality polyester fiberfill (you will want to stuff this very firmly so it holds its shape during sculpting).
  • Notions: A large-eye tapestry needle (crucial for the sculpting step), stitch markers (to mark the beginning of rounds), and scissors.
  • Stem Materials: A 3-inch piece of flat dark green ribbon or faux suede cord, and a small amount of hot glue or fabric glue to secure it.

Method

Starting the Ombre Sphere (1/5)

Start at the top of the pumpkin with the bright orange end of the ombre yarn. Make a magic ring. Rnd 1: 6 sc in ring (6). Rnd 2: inc in each st (12). Rnd 3: [sc, inc] 6 times (18). Rnd 4: [2 sc, inc] 6 times (24). Rnd 5: [3 sc, inc] 6 times (30). Rnd 6: [4 sc, inc] 6 times (36). Rnd 7: [5 sc, inc] 6 times (42). Rnd 8: [6 sc, inc] 6 times (48). Rnds 9-14: sc in each st around (48). The color will naturally begin to transition to reddish-orange as you work the even rounds.

Starting the Ombre Sphere

Decreasing and Stuffing (2/5)

As the yarn shifts to deeper reddish-orange, begin the decreases. Rnd 15: [6 sc, dec] 6 times (42). Rnd 16: [5 sc, dec] 6 times (36). Rnd 17: [4 sc, dec] 6 times (30). Rnd 18: [3 sc, dec] 6 times (24). Stop here and stuff the pumpkin very firmly with fiberfill, ensuring it holds a wide, rounded shape. Rnd 19: [2 sc, dec] 6 times (18). Rnd 20: [sc, dec] 6 times (12). Rnd 21: dec 6 times (6). Fasten off, leaving a very long tail (at least 36 inches) for sculpting.

Decreasing and Stuffing

Sculpting the Segments (3/5)

Thread the long tail onto a tapestry needle. To create the characteristic pumpkin lobes, insert the needle straight up through the bottom center hole and out through the top center. Pull the yarn firmly down the outside of the pumpkin back to the bottom center, pulling tightly to compress the stuffing and create a deep vertical groove. Insert the needle back up through the center to the top.

Sculpting the Segments

Completing the Lobes (4/5)

Continue this cinching process, wrapping the yarn around the outside and down through the center, spacing the grooves evenly. Create 6 to 8 equal segments around the pumpkin. Pull each pass very tight to ensure the fabric indents deeply. Once all segments are formed, tie the yarn securely at the bottom center, weave in the end, and trim any excess.

Completing the Lobes

Attaching the Ribbon Stem (5/5)

Take a 3-inch piece of flat dark green ribbon or faux suede cord. Fold it in half to create a loop. Apply a small amount of hot glue or fabric glue to the cut ends of the ribbon, and firmly press them deep into the center depression at the top of the pumpkin. Hold in place until secure.

Attaching the Ribbon Stem

Sculpting the segments

The segments are made by pulling lines tight across the stuffed body. Stuff firmly and evenly first, then pull each line to the same tightness so the lobes come out equal; a lumpy pumpkin gives uneven segments. An ombre or gradient yarn changes colour by itself as you work, so you do not need to change yarn between rounds.

For a set, make a trio using different sections of the ombre yarn: one mostly bright orange, one mixed and one deep red. The pumpkins look good together in a wooden dough bowl on a dining table or on a fireplace mantel. Questions about the pattern? Send them through the contact page.

Note: The images in this post are AI-generated illustrations, not photos of finished items.

Post Rating

★★★★★
5.0 (1 rating)
★★★★★

Related Posts