Chunky Ribbed Crochet Cowl Pattern for Beginners

Abdessamad avatar
Woman wearing a chunky terracotta ribbed crochet cowl over a cream sweater

A cowl is the fastest way to turn a single skein of chunky yarn into something wearable, and this one uses just one stitch. The half double crochet is worked into its “third loop”, which gives dense, stretchy vertical ribs that hug the neck and lie flat without curling. The strip is worked in rows and seamed into a loop at the end, so there is no joining in the round to worry about. If you can chain and make a half double crochet, you already know everything this pattern needs.

Cowl at a glance
Skill level Beginner
Time About 3 hours
Finished size (adult) About 24 in (61 cm) around and 10 in (25 cm) tall
Stitches ch, hdc, hdc in the third loop, sl st
Gauge About 10 sts and 10 rows = 4 in (10 cm) in ribbing. The ribbing stretches, so an exact match is not needed.

What you need

  • Yarn: super bulky (weight 6), about 120 yards (110 m). One 100 g skein is usually enough for the adult size.
  • Hook: 9 mm (M/N-13). Go up a size if your fabric feels stiff. This hook guide explains how sizes work.
  • Tools: yarn needle, scissors, a stitch marker, and a tape measure.

New to the shorthand? The stitch abbreviations chart and the hook and yarn chart are free to use while you work.

The one stitch to learn first

Every half double crochet has three loops on top: the front loop, the back loop, and a third loop, which is a horizontal bar on the back of the stitch just below the other two. Working into that third loop pushes the front and back loops forward and leaves a clean ridge on the face of the fabric. Rows made this way look like knit ribbing.

To find it: turn the stitch toward you so you are looking at the side facing you. Below the V at the top you will see a small horizontal bar. Insert your hook under only that bar, yarn over, pull up a loop, yarn over again and pull through all three loops on the hook. Practice on three or four stitches before starting the cowl.

Make the cowl

Stage 1: Chain the height

Make a slip knot and chain 26 loosely. The chain sets the height of the cowl, so a loose chain keeps the bottom edge as stretchy as the rest of the fabric. For another size, see the size table below.

Hands holding a wooden crochet hook and a loose chain of chunky terracotta yarn

Stage 2: Work the first row

Hdc in the 3rd chain from the hook, then hdc in each chain across. You should have 24 hdc. The two chains you skipped at the start count as the turning chain, so do not count them as stitches. Place a stitch marker on this row so you know which edge is the start. Chain 2 and turn.

Hands working the first row of half double crochet in chunky terracotta yarn

Stage 3: Switch to third-loop stitches

Row 2: hdc in the third loop of the first stitch, then in the third loop of every stitch across, ending in the last hdc of the previous row (24 sts). The chain 2 at the start does not count as a stitch, so the first hdc goes into the very first stitch of the row. Chain 2 and turn. Repeat this row for the entire length of the cowl.

Crochet hook going under the third loop of a half double crochet stitch in ribbed fabric

Stage 4: Keep going until it is long enough

Repeat Row 2 until the strip measures about 24 inches (61 cm) long when gently stretched, which is roughly 60 rows. Count your rows if you want a second cowl to match, but go by the tape measure, because yarn and tension vary. Check that you still have 24 stitches every few rows. Chunky yarn hides a missed stitch until the edge starts to curve.

Long terracotta ribbed crochet strip laid out on a table next to a tape measure

Stage 5: Seam the loop

Fasten off, leaving a 20 inch tail. For a plain loop, fold the strip so the two short ends meet with the right sides together. For an infinity look, give the strip one half twist first. Thread the tail on a yarn needle and whipstitch the ends together, going through the edge stitch of each side so the ribs line up. Slip stitching with the hook works too, but the seam is bulkier. Weave in all ends and turn the cowl right side out.

Hands seaming the ends of a terracotta ribbed crochet strip with a yarn needle

Pick your size

The chain sets the height and the row count sets the circumference. Rounding to even numbers keeps the stitch count easy to follow.

Size Starting chain Stitches per row Height Length before seaming
Child Chain 20 18 hdc about 7 in (18 cm) about 20 in (51 cm)
Adult Chain 26 24 hdc about 10 in (25 cm) about 24 in (61 cm)
Oversized Chain 30 28 hdc about 11 in (28 cm) about 28 in (71 cm)

Stitch counts are always the starting chain minus 2. Larger sizes need more yarn, so add a second skein for the oversized version.

When something goes wrong

  • The edges look wavy. You probably gained or lost a stitch. Count each row and make sure the last hdc goes into the last stitch of the previous row, not the turning chain.
  • The ribs are hard to see. The third loop is easy to miss. Look for the horizontal bar below the V, and if you are working into the V itself, back up and redo the row.
  • The fabric feels stiff. Go up to a 10 mm hook, or relax your tension on the third-loop stitches.
  • The cowl is too tight. Add 4 to 6 rows before seaming, or work a larger size next time.

Quick answers

Can I use a thinner yarn?

Yes. Use a bulky (weight 5) yarn with an 8 mm hook, and chain more to keep the same height, since each stitch is narrower. Test a small swatch to find your stitches per inch, and then calculate the chain you need.

How do I wash it?

Check the yarn label. Acrylic can usually go through a gentle machine cycle, while wool and wool blends should be hand washed in cool water and dried flat. Do not hang a wet cowl, because the weight of the water stretches the ribs.

Can I make it wider so it doubles over?

Yes. Start with a chain of 36 (34 hdc), make the strip about 22 inches long, and fold it in half lengthwise when you wear it for a thicker double layer.

Ideas for your next cowl

  • Use a self-striping or ombre yarn to turn the ribs into color bands.
  • Sew a row of buttons on one end and a row of loops on the other for a buttoned collar.
  • Add a tassel or a pom-pom to each corner for a scarf version, leaving the strip unseamed.

Questions about the pattern? Send them through the contact page.

Note: The images in this post are AI-generated illustrations, not photos of finished items.

Post Rating

★★★★★
No ratings yet
★★★★★

Related Posts