This Frankenstein’s Monster Crochet Candy Bowl is a cylindrical amigurumi-style bowl worked in stiff worsted weight yarn, with a jagged black hairline, grey neck bolts and black stitched scars. It is an intermediate pattern that needs working in the round and creating gaps by skipping stitches. The finished bowl is about 6 inches in diameter and 6.5 inches tall.
Before you begin
Skill Level: Intermediate (requires knowledge of working in the round, creating gaps by skipping stitches, and working spike stitches). Finished Size: Approximately 6 inches in diameter and 6.5 inches tall. Gauge: 4 sc stitches and 4 rounds = 1 inch (using worsted weight yarn and a 4.0mm hook).
What do the abbreviations mean?
sc = single crochet, inc = increase (2 sc in one stitch), ch = chain, sl st = slip stitch, rnd = round, st(s) = stitch(es).
Materials list
- ☐ Worsted Weight Yarn (Category 4):
- Lime Green: Approx. 120 yards (Main body, nose, ears)
- Black: Approx. 40 yards (Hairline, scar embroidery)
- White: Approx. 5 yards (Eye whites)
- Grey: Approx. 10 yards (Neck bolts)
- ☐ Crochet Hook: Size G / 4.0mm (or size needed to obtain a stiff gauge).
- ☐ Notions: Two 12mm black plastic safety eyes with washers, tapestry needle for sewing and embroidery, stitch markers to keep track of rounds, and scissors. (Note: No stuffing is required for this project).
The plan
To construct this Frankenstein’s Monster Candy Bowl, we will be working from the bottom up in continuous, unjoined rounds. The pattern begins with a standard flat circular base worked in lime green. Once the base reaches the correct diameter, we work a round in the back loops only (BLO) to create a sharp 90-degree turn, transitioning from the flat bottom to the vertical cylindrical walls. Halfway up the body, the pattern utilizes a ‘chain and skip’ method: we will chain stitches and leave the corresponding stitches below unworked, turning rows temporarily before bridging the gap to form the wide, open mouth. After the mouth is formed, we switch to black yarn. Here, you will use varying lengths of spike stitches dropping into the green rows below to create a jagged, realistic-looking hairline. Finally, we crochet small modular attachments—white eye circles, a little green nose, green ears, and grey neck bolts—and assemble them onto the face before embroidering his iconic black scars.
Work through it
Part 1: Base and Lower Body
Using lime green worsted weight yarn, start with a magic ring. Rnd 1: 6 sc in ring (6 sts). Rnd 2: inc in each st around (12 sts). Continue increasing by 6 sts each round until Rnd 8: [6 sc, inc] 6 times (48 sts). Rnd 9: Working in back loops only, sc in each st around (48 sts) to turn the edge. Rnds 10-15: sc in each st around (48 sts). The flat base and lower cylindrical wall are now formed.

Part 2: Mouth Opening and Hairline
To create the mouth opening, Rnds 16-20: sc in next 36 sts, ch 1, turn, leaving 12 sts unworked to form the gap. Rnd 21: ch 12 to bridge the gap, sc in the 36 sts (48 sts total). Rnds 22-25: sc in each st and ch around (48 sts). Change to black yarn. Rnd 26: work alternating single crochets and long spike stitches (inserting hook 1, 2, or 3 rows below) to create a jagged hairline around the circumference. Rnds 27-29: sc in each st around (48 sts). Fasten off.

Part 3: Facial Features and Bolts
Crochet the attachments. Eye whites (make 2): with white yarn, 6 sc in magic ring, sl st to join. Fasten off. Nose (make 1): with green, 6 sc in magic ring, Rnd 2: [sc, inc] 3 times (9 sts), Rnd 3: sc around. Fasten off. Ears (make 2): with green, 6 sc in magic ring, inc in each (12 sts), sc around. Fasten off. Grey Bolts (make 2): with grey yarn, 6 sc in magic ring, Rnd 2: in back loops only, sc around (6 sts), Rnds 3-4: sc around. Fasten off.

Part 4: Eyes, Nose, and Ear Assembly
Position the white eye circles on the face above the mouth. Insert black plastic safety eyes through the center of the white circles and push them entirely through the green bowl fabric, securing them on the inside with washers. Using a tapestry needle and the yarn tails left on the pieces, sew the green nose firmly to the center of the face between the eyes. Sew the green ears to the upper sides of the head, aligned horizontally with the eyes.

Part 5: Attaching Bolts and Embroidering Scars
Sew the two grey neck bolts to the lower sides of the green bowl body, just below the level of the ears. Thread a tapestry needle with a length of black yarn and embroider horizontal and vertical straight stitches to create Frankenstein’s iconic scars: place one cluster near the top corner of the mouth, and another angled above one eye. Finish the edge of the mouth opening with a round of slip stitches in green to neaten the rectangular border. Weave in all loose ends.

Making the bowl sturdy
A candy bowl needs a firm fabric, so use the hook size that gives a stiff gauge (4 sc and 4 rounds to the inch). A back-loop-only round turns the flat base into vertical walls, and the spike stitches halfway up set the shape, so work both carefully. For hygiene, fill the bowl with individually wrapped sweets only, because yarn is hard to clean.
Styling Your Finished Monster
Set the bowl on a fluffy white or black surface with a few extra candies around the base and some plastic spiders for a Halloween display. You can change the monster’s skin color, for example to pale purple or eerie grey, or add more embroidered details. Questions about the pattern? Send them through the contact page.
Note: The images in this post are AI-generated illustrations, not photos of finished items.
